Just installed my GReddy Type RS BOV. a little help

[FreaKEN-Rican]

All is quiet in libraryville. you can hear a pin drop when I shift gears, with a little bit of blow off. Now, maybe its because I am used to the 210 decible-louder than an air horn- RFL BOV, but isn't the Greddy supposed to sound a little louder and not like a mouse fart? I have it connected to where the Turbo XS BOV was connected to. I also pulled out all nessesary lines no longer needed with the Stage1.(uhh, I did this before the Greddy went in so its not the lines). with a 17PSI spike AND hold, I am not loosing boost and it still does blow off but man, It does sound a little too low. Do I need to make it really tight
? really loose? Or do I connect it somewhere else? :confused:

[Frodo]

the rs is not a loud bov... it is just kind of a whoosh shound and that is it

[hozay09]

^^ what he said. You can loosen the nut to make it a little bit louder but not much. Believe me, its 100x's better then the RFL.

[Broken5hift]

my HKS goes SKR EEEEEeeeeeeeeeeeeeeeeeeeeeeeeeeeeee e ee e


i love that........ dammit now i wanna take my srt-4 out

[BlackDragon]

Ken, loosen the locknut and then turn the set screw a few turns counterclockwise. keep trying it until you can get it to start blowing off at around -1 to 1 psi, and then it should sound quite nice.

[FreaKEN-Rican]

Thanks Ant. I'll try that. I know the Greddy is better and its not that I dont like it, I love it. I just thought it sounded a little bit louder thats all.

[Frodo]

Thanks Ant. I'll try that. I know the Greddy is better and its not that I dont like it, I love it. I just thought it sounded a little bit louder thats all.
try and find a type-s, mine is pretty loud

[hozay09]

try and find a type-s, mine is pretty loud

Don't forget annoying and will leak under high boost.

[Daryl]

Don't forget annoying and will leak under high boost.
Always hating!

[psi chick]

Don't forget annoying and will leak under high boost.

it held just fine for me on s2, i think he'll be fine :D

[Frodo]

Don't forget annoying and will leak under high boost.
good thing neither of us are running high boost :cool: and what about it is annoying? i love the way it sounds, but whatever

[DrEdSrT4]

TYPE S>ALL

ecspecially my freak one.. it matches my open downpipe well

[hozay09]

Always hating!
I got nothin' but love!


it held just fine for me on s2, i think he'll be fine :D

:liar:

good thing neither of us are running high boost :cool: and what about it is annoying? i love the way it sounds, but whatever

I keep forgetting I dont have a big turbo anymore :brutal_26

[psi chick]

not lying...it did hold just fine. i went to the rs when i decided to go s3. i found a really good deal and couldn't pass it up.....

[Frodo]

I got nothin' but love!



:liar:


I keep forgetting I dont have a big turbo anymore :brutal_26
u are so bipolar haha:kissey:

[Nolimits]

I like the Type S over the Type RS, so what if it leaks, BOV's are meant to be noticed!

[hozay09]

I like the Type S over the Type RS, so what if it leaks, BOV's are meant to be noticed!

:BangHead:

[DrEdSrT4]

I like the Type S over the Type RS, so what if it leaks, BOV's are meant to be noticed!

lmfao... brett could fill a book with those kind of comments..

[Frodo]

I like the Type S over the Type RS, so what if it leaks, BOV's are meant to be noticed!
yet another great brett comment

[FreaKEN-Rican]

OK another ?. if it blows off at less then 1 PSI. Lets say around 5PSI VAC. Is it too tight? or too loose.

[Frodo]

OK another ?. if it blows off at less then 1 PSI. Lets say around 5PSI VAC. Is it too tight? or too loose.
not to be a stickler but vac is measured in inches of mercury (inhg) not psi... if your bov is blowing off in vac, that means u need to tighten it

[Hassviper]

Hey about the hks, anyone know anything about the differnt inserts?

[hozay09]

Hey about the hks, anyone know anything about the differnt inserts?

The purple has a less high pitched sound and the gold is about the same as normal.